Thermoluminescent dosimeters (TLD-100) for absorbed dose measurements in alpha-emitting radionuclides.

Early works that used thermoluminescent dosimeters (TLDs) to measure absorbed dose from alpha particles reported relatively high variation (10%) between TLDs, which is undesirable for modern dosimetry applications. This work outlines a method to increase precision for absorbed dose measured using TLDs with alpha-emitting radionuclides by applying an alpha-specific chip factor (CF) that individually characterizes the TLD sensitivity to alpha particles. Variation between TLDs was reduced from 21.8% to 6.7% for the standard TLD chips and 7.9% to 3.3% for the thin TLD chips. It has been demonstrated by this work that TLD-100 can be calibrated to precisely measure the absorbed dose to water from alpha-emitting radionuclides.

Studies of thermoluminescence properties of liquid crystalline N-phenyl substituted phenyl polysiloxane hydroxamic acids.

The investigation of thermoluminescence (TL) glow curves in liquid crystalline side chain N-phenyl-substituted phenyl polysiloxane hydroxamic acids (PHAs) has yielded significant insights. These polymers demonstrated TL behavior when exposed to ß-radiation between 0 and 220°C, indicating inherent luminescent properties when irradiated. Notably, a dose-dependent relationship was observed in reported derivatized polymers; this study elucidates the diverse TL characteristics exhibited by various liquid crystalline side chain N-phenyl-substituted phenyl PHAs when exposed to ß-radiation. Understanding these dose-dependent and dose-independent behaviors enhances the knowledge of their luminescent properties and potential applications in radiation detection.

Photoluminescence and thermoluminescence dosimetry properties of Ag/Y co-doped ZnO nanophosphor for radiation measurements.

This work explores the thermoluminescence (TL) and photoluminescence (PL) properties of Ag/Y co-doped zinc oxide (ZnO) nanophosphor. The proposed dosimeter was prepared by the coprecipitation method and sintered at temperatures from 400°C to 1000°C in an air atmosphere. Raman spectroscopy was studied to investigate the structural features of this composition. The new proposed dosimeter revealed two peaks at 150°C and 175°C with a small shoulder at high temperature (225°C). The PL spectrum showed strong green emissions between 500 to 550 nm. The Raman spectrum showed many bands related to the interaction between ZnO, silver (Ag), and yttrium oxide (Y2 O3 ). The rising sintering temperature enhanced the TL glow curve intensity. The Ag/Y co-doped ZnO nanophosphor showed an excellent linearity index within a dose from 1 to 4 Gy. The minimum detectable dose (MDD) of the Ag/Y co-doped ZnO nanopowder (pellets) equaled 0.518 mGy. The main TL properties were achieved in this work as follows: thermal fading (37% after 45 days at 1 and 4 Gy), optical fading (53% after 1 h and 68% after 6 h by exposure to sunlight), effective atomic number (27.6), and energy response (flat behavior from 0.1 to 1.3 MeV). Finally, the proposed material shows promising results nominated to be used for radiation measurements.

Measurement of Hp(10), Hp(3) and Hp(0.07) to medical staff in endoscopic retrograde cholangiopancreatography, using thermoluminescence dosimetry.

Endoscopic retrograde cholangiopancreatography (ERCP) is widely used in the diagnosis and treatment of pancreatic and bile duct disorders. The procedure is performed under the guidance of fluoroscopy. This study aims to investigate the dose received by staff in the Endoscopy Department of AbuAli Sina Medicine and Organ Transplant Hospital in Shiraz. The dosimetry was performed using thermoluminescent dosemeters (TLD), type TLD-100. The values of Hp(10), Hp(3) and Hp(0.07) were estimated for the staff for 2 months. According to the results obtained in this study, the equivalent dose of the gastroenterologist's body, eye lenses and hands was 0.045 ± 0.001 mSv, 0.111 ± 0.014 mSv and 0.357 ± 0.034 $\mathrm{mSv}$, respectively. This study showed that the annual radiation exposure for ERCP department staff of Abu Ali Sinai Hospital is less than the annual dose limit. However, if the principles of proper radiation protection and individual dosimetry are followed, the dose to staff members can be reduced.

Comparison of the performance of two thermoluminescent dosimetry systems for the personal dose-equivalent Hp(10) measurement.

The performance of two thermoluminescent dosimetry systems (RGD-3D and RE2000) manufactured in China and Finland was compared. Both of these dosimetry systems demonstrated satisfactory results as their performance met the requirements of the standard. The two dosimetry systems showed similar performance in the energy response. The RGD-3D dosimetry system performed better in nonlinear response, minimum detectable level and blind sample tests, whereas the RE2000 dosimetry system showed better stability.

The effect of cooling rate on the precision of measurement of glow peak 5 in the thermoluminescence of LiF:Mg,Ti (TLD-100).

The effect of natural rapid cooling and oven slow cooling on the precision of thermoluminescence measurements of LiF:Mg,Ti is investigated. Three separate series of measurements resulted in average precisions of 5.1 and 5.0%, respectively. However, the highest precision of 1.7% (1 SD) was achieved for an oven-cooled material.

Synthesis and characterization of high-sensitivity Dy,Eu co-doped CaSO4 thermoluminescent phosphor using coprecipitation technique.

In this work, (99 - x)CaSO4 -Dy2 O3 -xEu2 O3 , (where x = 0, 0.05, 0.1, 0.2, 0.3, 0.4, 0.5) thermoluminescence phosphors were prepared using a coprecipitation method. The thermoluminescence (TL) dosimetry (TLD) characteristics such as TL sensitivity, dose-response, minimum detectable dose, thermal fading, and the effect of sunlight on the prepared phosphors were investigated. The obtained results indicated that the most sensitive phosphor was obtained at x = 0.05. Large thermal fading of 6% after 1 h and 26% after 24 h from irradiation followed by 71% after 1 month with no additional fading was observed within a time frame exceeding 2 months throughout the remaining duration of the investigation, which also spanned over 2 months. Despite the phosphor's high fading rate, the relative sensitivity of the prepared samples was ~90% compared with TLD-100. The marked effect of day sunlight was also determined. High dose-response within the low-dose range from 0.01 to 5 Gy was observed. The obtained results suggested that the synthesized phosphor is well suited for applications involving radiation biology and radiotherapy dosimetry.

Luminescence and dosimetry approach in terbium(III)-activated tungstate double perovskite.

A series of tungstate double perovskite Ca3 WO6 doped with Tb3+ was prepared by a combustion process using urea as a flux. The crystal structure identification of Ca3 WO6 :Tb3+ phosphors was done using X-ray diffraction patterns, and a monoclinic structure was discovered. The Fourier transform infrared spectrum of Ca3 WO6 :Tb3+ displayed characteristic vibrations of tungstate bonds. Under 278 nm excitation, Ca3 WO6 :Tb3+ exhibited intense downconversion green emission, which corresponded to the 5 D4 -7 FJ (J = 4,5) transitions of Tb3+ . The phosphor exhibited the highest photoluminescence (PL) intensity when it was doped with 1 mol% of Tb3+ ; later intensity quenching appeared to be due to the multipolar interaction at higher dopant concentrations. Moreover, high-quality thermoluminescence (TL) was detected when phosphors were irradiated using beta rays. The effects of Tb3+ concentration and beta dose on TL intensity were the two major aspects studied in detail. The TL intensity demonstrated excellent linear response to the applied range of beta dose. The trap parameters of the studied phosphors were computed by the peak shape approach and glow curve deconvolution. The fading effect on TL intensity was studied by recording the TL glow curves after 1 month of beta irradiation. Obtained results from the PL and TL characterizations showed that the phosphors under study have the potential to be used in lighting displays and in thermoluminescence dosimetry.

Thermoluminescence Characteristics of Copper and Terbium Co-Doped Lithium Tetraborate Glass.

In this study, the preparation and characterization of copper (Cu) and terbium (Tb) co-doped lithium borate glass using spectroscopic and thermoluminescence techniques are reported. A thermal treatment was introduced to increase the degree of crystallinity. The thermoluminescence glow curve signal of the samples displayed upon exposure to beta radiation was measured and analyzed. It was found that the samples doped with 0.1% of copper and co-doped with 0.3% terbium showed the highest thermoluminescent (TL) signal in response to the irradiated dose. The analyses revealed that the glow curves of the doped samples were composed of nine overlapping glow peaks with activation energies between 0.73 and 2.78 eV. As a whole area under the glow curve, the TL signals displayed a linear dose response in the range from 110 mGy to 55 Gy. The minimum detectible dose of the samples was found to be 10.39 µGy. It was found that peaks 1 and 2 disappear after one day of storage. The rest of the peaks (3-9) remain almost constant up to 74 days of storage.

IAEA/WHO postal dosimetry audit methodology for electron beams using radio photoluminescent dosimeters.

BACKGROUND: Independent dosimetry audits are an important intervention in radiotherapy for quality assurance. Electron beams, used for superficial radiotherapy treatments, must also be tested in dosimetry audits as part of a good quality assurance program to help prevent clinical errors. PURPOSE: To establish a new service for IAEA/WHO postal dosimetry audits in electron beams using RPL dosimeters. METHODS: A novel postal audit methodology employing a PMMA holder system for RPLDs was developed. The associated correction factors including holder dependence, energy dependence, dose response non-linearity, and fading were obtained and tested in a multi-center (n = 12) pilot study. A measurement uncertainty budget was estimated and employed in analyzing the irradiated dosimeters. RESULTS: Holder and energy correction factors ranged from 1.004 to 1.010 and 1.019 to 1.059 respectively across the energy range. The non-linearity and fading correction models used for photon beams were tested in electron beams and did not significantly increase measurement uncertainty. The mean dose ratio ± SD of the multi-center study was 1.001 ± 0.011. The overall uncertainty budget was estimated as ± 1.42% (k = 1). CONCLUSIONS: A methodology for IAEA/WHO postal dosimetry audits in electron beams was developed and validated in a multi-center study and is now made available to radiotherapy centers as a routine service.

Development of ring radiation dosemeters using 3D printing.

Extremity radiation monitoring is an important tool for the assessment of occupational exposures to staff at a variety of workplaces where ionising radiation is used. This work shows the feasibility of applying 3D printing for the development of customisable ring dosemeters. The rings were developed using two types of resin, hard and flexible and has the possibility of sterilisation using different techniques. The printed ring dosemeter was associated with BeO optically stimulated dosemeters. The energy and angular response were found within ±20% in the energy range from 24 to 662 keV and from 0° to 60° angle of incidence. This contributes to the reduction of measurement uncertainty when compared with currently used thermoluminescent detectors dosemeters. The new ring dosemeter showed a satisfactory response with respect to the performance criteria of the IEC 62387 Standard, in addition to providing improved ergonomics in relation to the commercial ring dosemeter.

Dosimetry of the PIM1 Pion Beam at the Paul Scherrer Institute for Radiobiological Studies of Mice.

Significant past work has identified unexpected risks of central nervous system (CNS) exposure to the space radiation environment, where long-lasting functional decrements have been associated with multiple ion species delivered at low doses and dose rates. As shielding is the only established intervention capable of limiting exposure to the dangerous radiation fields in space, the recent discovery that pions, emanating from regions of enhanced shielding, can contribute significantly to the total absorbed dose on a deep space mission poses additional concerns. As a prerequisite to biological studies evaluating pion dose equivalents for various CNS exposure scenarios of mice, a careful dosimetric validation study is required. Within our ultimate goal of evaluating the functional consequences of defined pion exposures to CNS functionality, we report in this article the detailed dosimetry of the PiMI pion beam line at the Paul Scherrer Institute, which was developed in support of radiobiological experiments. Beam profiles and contamination of the beam by protons, electrons, positrons and muons were characterized prior to the mice irradiations. The dose to the back and top of the mice was measured using thermoluminescent dosimeters (TLD) and optically simulated luminescence (OSL) to cross-validate the dosimetry results. Geant4 Monte Carlo simulations of radiation exposure of a mouse phantom in water by charged pions were also performed to quantify the difference between the absorbed dose from the OSL and TLD and the absorbed dose to water, using a simple model of the mouse brain. The absorbed dose measured by the OSL dosimeters and TLDs agreed within 5-10%. A 30% difference between the measured absorbed dose and the dose calculated by Geant4 in the dosimeters was obtained, probably due to the approximated Monte Carlo configuration compared to the experiment. A difference of 15-20% between the calculated absorbed dose to water at a 5 mm depth and in the passive dosimeters was obtained, suggesting the need for a correction factor of the measured dose to obtain the absorbed dose in the mouse brain. Finally, based on the comparison of the experimental data and the Monte Carlo calculations, we consider the dose measurement to be accurate to within 15-20%.

Comparison of absorbed doses and organ doses measured with thermoluminescent dosimeters and Gafchromic film for cone beam computed tomography examination of the posterior mandibular region in a head phantom.

OBJECTIVES: We aimed to map the correlation between thermoluminescent dosimeters (TLDs) and Gafchromic film for measuring absorbed doses and to compare minimum, maximum, and mean absorbed doses over larger regions of interest and at various craniofacial organs and tissues during cone beam computed tomography (CBCT) exposure of the mandibular third molar region. STUDY DESIGN: We positioned TLDs at 75 measurement points in a head phantom. Gafchromic film was cut to the same shape as the 5 levels of the phantom and was placed on top of the TLDs. Both dosimetry methods thus included the surface of each level simultaneously. CBCT scans were made using a 5 × 5 cm field of view and a rotation angle of 200°. Measurements included absorbed dose distributions, doses at all 75 points, and minimum, maximum, and mean doses within organs and tissues. RESULTS: The correlation of point-dose measurements at all TLD sites with doses measured on film was strong (R2 = 0.9687), with greatest correlation at lower doses (<2 mGy). Large deviations between TLD and film measurements of minimum and maximum doses and absorbed doses to the organs occurred at all 5 levels. TLD positioning failed to cover several organ sites; for these, only absorbed dose measurements from the film were available. CONCLUSIONS: TLDs were unable to sample dose distributions and gradients accurately. The characteristics of Gafchromic LD-V1 film make it a favorable alternative in dental CBCT dosimetry.

Thermoluminescence dosimeter (TLD) studies of Ca10 K(PO4 )7 :Dy phosphor for applications in radiation dosimetry.

This study reports the thermoluminescence (TL) aspects of Ca10 K(PO4 )7 :Dy phosphor synthesized using a wet chemical method for the first time. The X-ray diffraction (XRD) results confirm the formation of the desired crystalline phase. Surface morphological studies reveal the formation of polyhedrons and agglomerations having an average diameter of 200 nm, while energy dispersive X-ray spectroscopy (EDS) data show the presence and composition of the elements in appropriate amounts. The effect of Dy doping concentration has been studied on the TL properties with exposure to gamma radiations from the Co-60 source. The best TL response has been observed for 5 mol% Dy doping concentration. The glow curve is simple and consists of a single peak at 130°C. The effect of the heating rate has been studied on the TL glow curve, and the heating rate of 5°C/s shows the best TL response. The various TL properties such as annealing conditions, dose-response, TL linearity, fading, and reusability of the prepared phosphor have been studied to check its suitability as a good TL dosimeter (TLD). TL characterization of the phosphor reports that the TL response is linear from 5- to 2000 Gy. The results show that this phosphor can be a good TLD for the dosimetry of gamma radiations from Co-60.

A machine learning approach for correcting glow curve anomalies in CaSO4:Dy-based TLD dosimeters used in personnel monitoring.

The study presents a novel approach to analysing the thermoluminescence (TL) glow curves (GCs) of CaSO4:Dy-based personnel monitoring dosimeters using machine learning (ML). This study demonstrates the qualitative and quantitative impact of different types of anomalies on the TL signal and trains ML algorithms to estimate correction factors (CFs) to account for these anomalies. The results show a good degree of agreement between the predicted and actual CFs, with a coefficient of determination greater than 0.95, a root mean square error less than 0.025, and a mean absolute error less than 0.015. The use of ML algorithms leads to a significant two-fold reduction in the coefficient of variation of TL counts from anomalous GCs. This study proposes a promising approach to address anomalies caused by dosimeter, reader, and handling-related factors. Furthermore, it accounts for non-radiation-induced TL at low dose levels towards improving the dosimetric accuracy in personnel monitoring.

Optically stimulated luminescence detectors for dosimetry and LET measurements in light ion beams.

Objective.This work investigates the use of Al2O3:C and Al2O3:C,Mg optically stimulated luminescence (OSL) detectors to determine both the dose and the radiation quality in light ion beams. The radiation quality is here expressed through either the linear energy transfer (LET) or the closely related metricQeff, which depends on the particle's speed and effective charge. The derived LET andQeffvalues are applied to improve the dosimetry in light ion beams.Approach.OSL detectors were irradiated in mono-energetic1H-,4He-,12C-, and16O-ion beams. The OSL signal is associated with two emission bands that were separated using a pulsed stimulation technique and subjected to automatic corrections based on reference irradiations. Each emission band was investigated independently for dosimetry, and the ratio of the two emission intensities was parameterized as a function of fluence- and dose-averaged LET, as well asQeff. The determined radiation quality was subsequently applied to correct the dose for ionization quenching.Main results.For both materials, theQeffdeterminations in1H- and4He-ion beams are within 5 % of the Monte Carlo simulated values. Using the determined radiation quality metrics to correct the nonlinear (ionization quenched) detector response leads to doses within 2 % of the reference doses.Significance.Al2O3:C and Al2O3:C,Mg OSL detectors are applicable for dosimetry and radiation quality estimations in1H- and4He-ions. Only Al2O3:C,Mg shows promising results for dosimetry in12C-ions. Across both materials and the investigated ions, the estimatedQeffvalues were less sensitive to the ion types than the estimated LET values were. The reduced uncertainties suggest new possibilities for simultaneously estimating the physical and biological dose in particle therapy with OSL detectors.

Characterization of Thermoluminescent Dosimetry Systems According to the IEC 62387:2020 Standard.

ABSTRACT: A need for detailed testing of individual monitoring systems used in accredited service at the Vinca Institute of Nuclear Sciences was recognized following changes in individual, workplace, and environmental monitoring passive dosimetry systems acceptability criteria stated in IEC 62387:2020 and changes related to reference fields used in radiation protection defined in ISO 4037:2019. Reliability and accuracy of dosimetry data acquired by passive dosimetry systems used for individual monitoring is assured by carrying out type tests. In this manner, the effects of different radiation influence quantities are examined. Passive dosimetry systems comprised of an LiF:Mg,Ti (TLD-100) detector card placed in two different holder models (8814 and 8850) and the Harshaw TLD Model 6600 Plus Automated Reader were tested. Type tests were done in an extended range of photon energies from 40 keV up to 1.25 MeV, angle of incidence values of ±45° and ± 60° for both vertical and horizontal dosimeter orientation, and in the dose range from 0.05 mSv to 1 Sv. Both dosimetry system configurations perform in line with IEC 62387:2020 within mandatory range for tested influence quantities. Dosimeters that use the 8850 holder type showed less pronounced energy and angular dependence of the response in the low-energy range.

TL glow curve and kinetic analysis of Na2SiO3:Pr3+ under beta radiation effect.

Ionizing radiation dosimetry with thermoluminescence (TL) materials based on silicon or glass can be interesting in its potential use in radiation monitoring as the solution to the constant looking of development of new radiation detectors. In this work, TL characteristics of sodium silicate exposed to beta radiation effects were studied. TL response beta irradiated exhibited a glow curve with two peaks centered at 398 K and 473 K. Samples showed linearity from 0.55 to 13.2 Gy. TL readings after 10 times showed a repeatability with an error of less than 1%. Remain information showed significant losses during the first 24 h, but its information was almost constant after 72 h of storage. The Tmax-Tstop method exhibited three peaks which were mathematically analyzed with a general order deconvolution finding kinetic orders close to the second order for the first peak, meanwhile the kinetic order for the second peak and third peak are close to second order. Finally, the VHR method showed anomalous TL glow curve behavior with an increasing intensity TL as the heating rate increased.

Use of Thermoluminescence Dosimetry for QA in High-Dose-Rate Skin Surface Brachytherapy with Custom-Flap Applicator.

Surface brachytherapy (BT) lacks standard quality assurance (QA) protocols. Commercially available treatment planning systems (TPSs) are based on a dose calculation formalism that assumes the patient is made of water, resulting in potential deviations between planned and delivered doses. Here, a method for treatment plan verification for skin surface BT is reported. Chips of thermoluminescent dosimeters (TLDs) were used for dose point measurements. High-dose-rate treatments were simulated and delivered through a custom-flap applicator provided with four fixed catheters to guide the Iridium-192 (Ir-192) source by way of a remote afterloading system. A flat water-equivalent phantom was used to simulate patient skin. Elekta TPS Oncentra Brachy was used for planning. TLDs were calibrated to Ir-192 through an indirect method of linear interpolation between calibration factors (CFs) measured for 250 kV X-rays, Cesium-137, and Cobalt-60. Subsequently, plans were designed and delivered to test the reproducibility of the irradiation set-up and to make comparisons between planned and delivered dose. The obtained CF for Ir-192 was (4.96 ± 0.25) µC/Gy. Deviations between measured and TPS calculated doses for multi-catheter treatment configuration ranged from -8.4% to 13.3% with an average of 0.6%. TLDs could be included in clinical practice for QA in skin BT with a customized flap applicator.

Thermoluminescence properties of the rock naturally annealed for thousands of years by flames from the earth's inner layers.

The gas leak in Chimaera near Çirali, Antalya, has been active for thousands of years. It is also known to be the source of the first Olympic flame in the Hellenistic period. The sample taken from the Chimaere seepage annealed for thousands of years was determined to be calcite-magnesian (Ca, Mg)O3 . In this study, thermoluminescence (TL) properties of calcite-magnesian annealed for thousands of years in the fire caused by methane gas were investigated for particle size, dose-response, heating rate, and fading experiments. It exhibits a clear TL glow curve with two distinct peaks positioned at 160 and 330°C, and its shape is not affected by variation in applied dose and reproduciility of experiment. There is a wide linear relationship between TL output and applied dose up to 614 Gy. Although the positions of the TL peaks are stable with the cycle of measurement, a poor reusability was observed in terms of the area under the TL glow curve and peak intensity.